Metric Imperial Cylinders 4 Displacement 1.3L (1298cc) 80.0cu.in Type single overhead camshaft Bore 74.0mm 2.91in Stroke 75.4mm 2.97in Compression Ratio 8.7;1 Compression pressure 1171.3-1371.1kPa 170-199psi Pressure difference allowance between cylinders 97.8kPa 14.2psi Valve Clearance cold Exhaust Valve 0.16-0.20mm 0.0063-0.0079in Intake Valve 0.13-0.17mm 0.0051-0.0067in Valve Clearance Hot Exhaust Valve 0.26-0.30mm 0.0102-0.0118in Intake Valve 0.23-0.27mm 0.009-0.011in Cylinder Head to engine block surface warpage 0.05mm 0.002in to exhaust manifold surface warpage 0.1mm 0.004in to intake manifold surface warpage 0.1mm 0.004in valve guide bore diameter intake and exhaust valves 12.030-12.048mm 0.4736-0.4743in valve seat angle intake and exhaust valves 45º valve seat width intake and exhaust valves 1.3-1.5mm 0.0512-0.0590in Valves ,Valve Springs and camshaft
Cam Height (base circle & lift) fuel pump lobe 39.6-40.0mm 1.5590-1.5748in intake and exhaust lobes 37.4-37.5mm 1.4724-1.4763in camshaft run-out 0.10mm 0.0039in camshaft thrust clearance 0.75mm 0.0295in camshaft to jounal clearance 0.050-0.150mm 0.0020-0.0050in contact seat with intake and exhaust valves 1.3-1.5mm 0.0512-0.0590in stock allowance of valve stem end face 0.5mm 0.019in valve guide inside diameter intake and exhaust valves 7.000-7.015mm 0.2756-0.2761in valve guide protrusion intake and exhaust vealves 14mm 0.56in valve guide to valve stem clearance intake valve 0.02-0.07mm 0.0008-0.0027in exhaust valve valve head margin intake valve 0.6-1.0mm 0.0236-0.0390in exhaust valve 0.02-0.07mm 0.0275-0.0390in valve head radial run-out 0.08mm 0.003in valve spring free lenth 48.1-49.3mm 1.8937-1.9490in valve spring preload intake and exhaust 22.8-29.2kg @ 41.5mm 50.2-64.3lbs @1.63in valve spring sqareness 2.0mm 0.079in valve stem diameter exhaust valve 6.950-6.965mm 0.2737-0.2748in intake valve 6.965-6.980mm 0.2742-0.2748in valve stem deflection exhaust valve 0.18mm 0.007in intake valve 0.14mm 0.005in Rocker arm shaft and rocker arms rocker arm inside diameter 16.000-16.018mm 0.629-0.630in rocker shaft outside diameter 15.973-15.988mm 0.628-0.629in rocker shaft run-out 0.12mm 0.004in rocker shaft to arm clearance 0.045-0.09mm 0.0017-0.0035in Engine block Cylinder bore out-of-round and taper 0.10mm 0.0039in Cylinder bore-to-piston clearance 0.02-0.04mm 0.0008-0.0015in Engine block-to-cylinder head surface warpage 0.03-0.06mm 0.0012-0.0024in Standard cylinder bore 74.00-74.15mm 2.9134-2.9193in Pistons Piston pin diameter Piston ring groove width Oil ring second compression ring Top compression ring Standard piston diameter Piston rings End gap Oil ring Second compression ring Top compression ring Side clearance Oil ring Second copression ring Top compression ring Thickness Oil ring Second compression ring Top compression ring Camshaft and conecting rods Oil pump
